The Lawn Mowing Man

how to start your own lawn mowing business

 

LAWN MOWING TOOLS

buying, using, maintaining, repairing all types of lawn mowing tools in a lawn mowing business
All Of Those Visible Gaps Between Steel Plates Can Trap Wet Grass

Mowing wet grass in Winter is usually a challenge to lawn mowing contractors because the wet lawn clippings often clog the rear chute of our lawn mowers. The predominant reason that this happens is because all self propelled commercial lawn mowers in Australia have half of their rear chutes blocked off to allow room for the gearbox. This decreased chute space then greatly restricts the amount of lawn clippings that can be dispelled out of the rear chute as we mow lawns, this becomes an even greater problem when we are mowing wet grass in Winter, because the wet grass does not flow smoothly in millions of tiny light and dry pieces of grass, it instead clumps up together and becomes sticky, and then quickly and easily blocks the rear chute of our lawn mowers, which leads to our problem.

Some lawn mower manufacturers have since started putting in half chutes into some commercial push lawn mowers, which then creates the exact same problem of the lawn mowing contractors grievances in another machine, and for no real known reason. While some manufacturers have started to put blade brake clutches onto some push lawn mowers, this may or may not warrant the decision to block off half the rear chute, which then makes the lawn mower an absolute pain to use.

The same commercial lawn mowers from years past which didn’t have a half chute, and which had a full width rear chute would experience almost no clogging from wet grass at all.

Solutions To Mowing Wet Grass More Efficiently

Often when mowing wet grass the lawn mowing contractor will have to mow in narrower and narrower strips, to cut less grass with each pass, to try to have less grass pass through the rear chute of the lawn mower without constantly clogging it. This is our first option when mowing wet lawns or thicker overgrown lawns and when our rear lawn mower chutes are constantly becoming clogged by grass.

If we look closely at the inside of our rear chutes of our lawn mowers we will notice a steel plate at the bottom part of the chute opening and another steel plate covering the gearbox area. When we look alongside where those steel plates meet the alloy lawn mower chassis, and where they meet each other, we will see that none of these areas are too tightly fit together, but we will see gaps between the steel pieces. These gaps can allow small pieces of grass to catch in these places when mowing wet lawns. Once a little bit of grass is trapped in these places, then the only thing that will follow is that even more grass will collect onto the already trapped grass, and soon the chute will become clogged with wet grass regularly.

What we can do here is to put a strip of silicone along these gaps, so that there are no more gaps there at all, but rather a smooth surface for the grass to travel across, with much less likelihood of any grass finding any places in which to get caught.

Some commercial lawn mowers like the Honda HRU216 will run a combination of high lift and low lift blades. In Winter time we swap these blades over to all high lift, this creates greater wind velocity underneath the lawn mower and will help to dispel wet grass clippings with greater efficiency, which in turn will then allow the lawn mower to resist clogging of the rear chute more often.

Some lawn mowing contractors choose to run their lawn mower blade setups using all high lift blades all year round. Try it for yourself and see if you notice or prefer the differences in these two ways to run your own lawn mower blades setup.

A lawn mower with a blade brake clutch is an awesome thing when we are dealing with a half chute lawn mower that is constantly clogging with wet grass. Spinning lawn mower blades throwing wet grass all over us and risking our safety is just one less thing we need to think about when we need to unclog the rear chute and if we don’t want to turn the engine off every time we have to do it. We know that our hands are never at risk, and we know that if we use a piece of wood to unclog the rear chute that it won’t get hit by the lawn mower blades to then fly up in our faces.

 
Start A Lawn Mowing Business In Australia
 
how to start a lawn mowing business in australia
all articles and images are © copyright
thelawnmowingman.com
 
 

how to start a lawn mowing business in australia