The Lawn Mowing Man

how to start your own lawn mowing business

 

LAWN MOWING TOOLS

buying, using, maintaining, repairing all types of lawn mowing tools in a lawn mowing business
Honda HRU 216 Drive Clutch Cable

If our Honda HRU 216 lawn mower is having drive problems, if it’s hesitating when it’s supposed to be going forward, if the gearbox is making clicking noises, then the problem is almost always the drive cable which has become stretched over time with use. This is normal.

If our lawn mower is still near new, or if we replaced the drive cable a while ago ourselves, then we might only need to make an adjustment with the two adjusting nuts. Moving them along just a few millimetres will fix the problem.

If however, like in this photo, we have run out of room to adjust these nuts anymore, then it’s time to replace the clutch cable on our lawn mower.

Honda Mower Clutch Adjustment

the clutch cable is in the middle - it has no more adjustment room left
 

The good news is, that this is a very quick and easy job to do, which I did in about 10 minutes on this changeover.

Some lawn mower mechanics like to change the clutch arm at the same time as they replace the clutch cable, as for only a few dollars more, and a few minutes longer, a full repair job has been done which will keep the lawn mower productive and reliable for the lawn mowing contractor, who definitely does not want unexpected breakdowns during their work days.

I did not replace the arm this time, because I replaced the gearbox on this lawn mower months ago and I didn’t replace the clutch cable when I did it, So in this case the clutch arm is not too old to be of any concern, and the clutch cable was significantly older.

Removing The Clutch Cable On A Honda HRU 216 Lawn Mower

The rear gearbox cover will need to be removed first. It is held in place by two bolts, one at the top of the rear chute section, and one underneath the mower.

Honda Mower Gearbox Cover

 

A stick will hold the rear chute flap open while we do our gearbox work.

Then I undo the two nuts at the control box.

The drive clutch cable is the middle cable.

Followed by using a pair of needle nose pliers to help detach the cable from the spring.

Then remove any zip ties that are holding the cable to the handles.

Leave the clutch cable lying towards the front and on the top of the lawn mower, this makes it much easier to work with the cable at the gearbox.

There is no need to remove the black plastic gearbox cover on top of the lawn mower.

I use a screwdriver to pull the spring down and out of position.

The cable is then lifted upwards and out of the hole which secures it at the gearbox.

Honda Mower Gearbox Adjustment

the clutch cable is very easy to detach - though sometimes it gets stuck
 

Then the inner cable is detached from the arm on the gearbox.

Honda Mower Gearbox Cable

the little arm is in full view - the nut to detach the arm is on the right side of the arm
 

That’s it.

Replacing Honda HRU 216 Gearbox Arm

I have no working photos for this part, so I’ll only narrate the process.

This might add another 10 minutes or longer to the clutch cable replacement

Look very carefully at the position of the arm in relation to the rest of the gearbox, do this while moving the arm up, and then again when moving the arm down.

We need to remember the exact position of the gearbox arm.

There is a little nut which holds a bolt in position on the arm, this needs to be undone and the little bolt removed.

The nut is at the top of the gearbox, while the bolt comes out from underneath the gearbox.

Honda Mower Gearbox Nut

looking from underneath the mower - the bolt is attached to the right side of the arm
 

The arm is then pulled directly out from the grooved pole that holds onto it, if the arm is stuck then use a screwdriver to help loosen it.

The new arm is put back into exactly the same position as the old arm was in, we check the up and down movements of the arm and check that the new arm is in the same position as the old arm.

If we are out by a single groove point in positioning the arm, then it might be impossible to attach the clutch cable to it, or the cable might be too loose and may not drive the lawn mower at all.

If we put the clutch cable back together again and it is wildly out of sync, then we need to detach the clutch cable from the arm, remove the arm, and reposition the arm until we get it right. It’s a pain, but it’s the only way it can be done.

Replacing The Clutch Cable On A Honda HRU 216 Lawn Mower

To replace the clutch cable is to do the same in reverse order.

With the cable lying over the front and on top of the lawn mower, attach the cable to the gearbox arm.

Honda Mower Gearbox Repair

here is the hole where the clutch cable sits into
 

Then use a screwdriver to push the spring down and into position.

Then lift the cable up to lock it into its position in the hole.

Honda Mower Gearbox Repair

the new clutch cable is attached in under a minute
 

Put the cable in position towards the top of the lawn mower handles.

With the help of needle nose pliers we attach the cable to the top spring.

Then we attach the cable in position in the top control box.

We want to attach the threaded part in about the halfway position between each end of the screw part, we then tighten the two nuts with our two 10mm spanners, the smaller the spanners the better.

We choose the halfway point, because we need to start somewhere when guessing where to tighten the nuts, so we start here, it’s usually about right.

Honda Mower Clutch Adjustment

the new clutch cable is in the middle - it now has lots of adjustment room
 

Then we test the mower to ensure the drive is working perfectly, and we then put the gearbox cover on the back of the lawn mower again, this can be a very tricky thing to do.

In our first couple of cuts after replacing the clutch cable, we may find that we’re still having issues, in this case we just adjust the clutch cable via those two adjusting nuts at the control box.

Tightening the clutch happens when there is less screw part shown towards the top of the mower handles, and so eventually when we run out of screw area on that part of the cable towards the top, then it will be nearing time to replace the clutch cable again.

 
Start A Lawn Mowing Business In Australia
 
how to start a lawn mowing business in australia
all articles and images are © copyright
thelawnmowingman.com
 
 

how to start a lawn mowing business in australia